- CHANGE PIN GENIE INTELLICODE KEYPAD SERIAL
- CHANGE PIN GENIE INTELLICODE KEYPAD CODE
- CHANGE PIN GENIE INTELLICODE KEYPAD SERIES
Follow the same procedure for each additional door you wish to program. Last, return the programming switch to ‘R’ (for RUN) and press the assigned transmitter button to test the door and start the door moving.Next, move the small programming switch to ‘S’ (for SET) and press the transmitter button you wish to have assigned to the above door.
CHANGE PIN GENIE INTELLICODE KEYPAD CODE
First, match the settings on the Internal Code Setting Switches with the same set of switches in the receiver on the garage ceiling, as described in the previous programming instructions. To program a button for one of your doors, follow the instructions below: The small left switch is for programming purposes. The small right switch should be set according to how many Code Setting Switches in your receiver (either 9 or 12). These garage door opener transmitters have 2 smaller switches to the right of the internal Code Setting Switches. Programming Multi-Button Digital Remotes with Internal Set Switches: Genie has been making the 390 MHz frequency exclusively for the last 15 years. Note: the frequency of the transmitter must be the same frequency as the receiver on the ceiling for it to work. The receiver is located either behind the light lens of the Genie garage door opener motor head, or inside an external small rectangular box on the ceiling, which is connected to the motor head by a set of wires. 
These transmitters work by matching the settings on the internal code setting switches with the same set of switches in the receiver on the garage ceiling. Programming Digital Remote Transmitters with Internal Set Switches
To re-program each remote follow steps 1 through 3 of the programing instructions relative to your opener above. 
All previously programmed remotes will no longer work with your door. While the long purple LED is blinking hold down on the UP and DOWN triangle buttons at the same time until both LEDs flash blue and go off.Follow steps 1 and 2 above or step 1 if between 2009 and July 8, 2011.The remote is then programmedĬlearing Memory for Remotes and Keypad (if present) Hold the new remote 4 or 5 feet away and press 3, 4 or 5 times until the door activates.To unlock the programming feature use a remote that already operates the unit and press it once.Press the square button once more until the long purple LED comes on and release. Press and hold down the square button on the motor head until the round blue LED comes on, then release the button.
CHANGE PIN GENIE INTELLICODE KEYPAD SERIAL
(see serial # on front: first 2 digits = year, next 3 digits = day of the year)
CHANGE PIN GENIE INTELLICODE KEYPAD SERIES
This clears the radio receiver’s memory.įor Genie IntelliG, TriloG Series built from 2009 until J( Intellicode III ) After Step 2, while the purple LED is blinking, press and hold both triangular button until the purple LED goes out. To clear all remotes and keypad from the system, follow Steps 1 and 2.
While the long LED is blinking, hold the remote 4 or 5 feet away and press 3, 4 or 5 times, until the door activates. ( Note: if the blue light stays on, go to instructions for Intellicode III, below ) The long purple LED button will start to blink. Press and hold down the square button on the motor head until the round blue LED light come on, then release the square button. Looking up in your garage at the bottom of your Genie motor cover is a set of black buttons, depicted in the drawing below, along with two LED lights shown here in grey. **To erase all Intellicode remotes and wireless keyless entry, hold down on the learn button until the indicator light stops blinking, then proceed to Step 1.įor Genie IntelliG, TriloG, SilentMax, PowerMax, GPower, and PowerLift Series Openers ( Intellicode II ) Press the transmitter button once more to test the system and start your door moving. (Keep the transmitter you want tuned at least 2 feet away from the power head while tuning.) After pressing the Learn Code Button once, press your transmitter button three times for your system to grab the frequency and code it in. When pressed, a radio signal indicator light will start blinking red for 30 seconds. This small, black, unmarked button is located behind the light lens at the motor head and is nearest the floppy 6 inch antenna wire that protrudes from the motor head. Gently press and release the Receiver Learn Code button on the power head receiver of your door operator. Programming Genie Intellicode Remote Transmitters Programming Opener Remotes Programming Instructions for Genie remotes:
0 kommentar(er)
